Mess Hall "Chef's Prep Island" with Double Sinks. Presently being coated with "Stainless Steel Polish" (paint). Will be fitted with 4 "stainless steel" pipe "Stanchion Legs" similar to the "Scullery Sink" (in the foregoing photo sets). Drain holes are already predrilled, and this set of Sinks will also be "plumbed" to be fully functional. Additionally, a rectangular utensil "rack" is being manufactured, with pipe stanchions to be installed at each corner of the sink unit, rising up 5 inches above the sinks, as a rack to hang utensils, hanging clean ladles, serving spoons, slotted spoons, pierced spoons, etc., for convenient reach for our "KPs", "First Cooks", "Mess Stewards", "Mess Officers", etc. that are working in the Kitchen of our "Mess Hall". "Drawer Cartridges" have been installed beneath Left Sink Apron and Right Sink Apron, for installation of "stainless steel" Drawers, allowing storage of clean "Chef Knives", Paring Knives", "Tongs", and other items that lack a "handle loop" for mounting the utensil over the overhead "Utensil rack". Finally, there will also be manufactured and installed, a rounded edge "stainless steel" water retaining fence all around these sinks, to prevent water splashing onto "Mess Hall" floors (similar to what you see existing on our "Scullery Sinks").

 

Mess Hall "Double Ovens" Cartridge being "stainless steel" polished (to aid in easier oven cleaning). Next step will be manufacturing and installation of "fiber optic" oven elements for each oven. Variable intensity, these "oven elements" will light up, and grow brighter RED as a "Chef" turns up the "oven temperature". The "oven element" will have a replaceable cartridge, if future replacement is needed. Power will be a safe 12 Volt "direct current" (or less) with low amperage, so our Small Soldiers do not receive any dangerous shocks. Once completed, the "Double Oven Cartridge" will be the centerpiece of our complete assembly, a "Double Oven", "Range" (6 Burner Stove), "Grill" (for pancakes, hash browns, fried eggs, cheeseburgers, etc.,) and working "Vent Hood" (with simulated "Fire Extinguisher" Cartridges on both sides of unit).

 

The "Double Oven" easily handles 4 "Deep Dish" Commercial Baking Pans. With 2 separate "ovens" a Chef can bake at 2 different temperatures, if desired. Once the foods have been "baked" (the ovens do NOT actually get HOT), a Chef uses thick silvered "Hot Pad Mittens" to remove the pans, and places them in an insulated "chiller/warmer selectable prepared foods transport cart" (scheduled for manufacturing as a separate product) for storage until meal time (so more batches of foods may be baked). These "Deep Dish Baking Pans" fit exactly into slots in our "Mess Hall Serving Line" (photos in the foregoing). Four "slots" are for pans of "Hot Foods" on the warm side of the "Mess Hall Serving Line", and four "slots" are for "Cold Foods" on the cool side of our "Mess Hall Serving Line". The insulated "Chiller/warmer selectable prepared foods Transport Carts" may be set (as your Chef desires) to warm or chill the (up to) 4 pans of foods contained therein, thus by having 2 of these Transport Carts, your Chefs can serve both Hot and Cold Foods, placing pans into the proper carts.

 

"Mess Hall" Dining Table receiving "stainless steel polish" (paint).

 

Doc Peterson testing for correctness of ergonomic design of "stainless steel" Mess Hall Dining Tables and Chairs.

 

Stainless Steel color "Mess Hall Dining Table" with Six "Walnut" color Medium Back Armchairs arranged for serving a Meal at Chowtime.

 

Doc Peterson tests the fit of our "Medical Desk & Chair".

 

Note the "privacy screen" on the front and sides of our "Medical Desk" so Female Nurses wearing Skirts do not have to worry about people staring at their legs (thus perhaps disturbing the Nurses' work efforts). Note from above photos of the "Medical Desk", how shiny our "Stainless Steel Polish" comes out (when multicoated and polished).

 

"Stainless Steel Polish" (paint) being applied to our "Instrument Scrub and Preparation Sinks" for our Hospital's "CMS". Similar to our Mess Hall "Chefs' Prep Island" (in the foregoing photo sets), this "Instrument Scrub and Preparation Sinks" will have 4 "stainless steel" pipe Stanchion Legs and Base. It will also have the "Water retaining rounded top fence" all around, as it will be a FULLY FUNCTIONAL SINK. It will NOT have an "Overhead Utensils Rack" as it does not need one. It does have a "Drawer Cartridge" preinstalled beneath the "LEFT Sink Apron" and the "RIGHT Sink Apron". The Drawers are used for storage of plastic bottles (LEFT Drawer) of "Instrument Detergent" and "Scrub Brushes" to clean Surgical Instruments, and (RIGHT Drawer) of "Instrument Milk" to lubricate Surgical Instruments after cleaning, and before they are packed up into "Instrument Packs" and sterilized in our "Autoclaves". After they are cleaned, dried, and lubricated at this Sink, they are assembled into "Surgical Procedure Packs" on our "Instrument Pack Preparation Table" (shown in photo following this one), then placed into either our "Ethylene Oxide Gas Sterilizer" or our "Steam Autoclave Sterilizer" (both items scheduled for manufacturing as separate products). After "sterilization" the "Surgical Packs" are returned to our "Instrument Preparation Table" and sealed in special "plastic wrap" to maintain longer term sterility. After that, the "Surgical Packs" are placed in inventoried positions in our "CMS Sterilized Surgical Pack Storage Cabinet" (scheduled for manufacturing as a separate product). For reasons of proximity & convenience, our "CMS" is located adjacent to our "Operating Room".

 

CMS "Instrument Surgical Pack Preparation Table".

 

Colonel AARON BANK inspects new delivery of Stainless Steel Items manufactured HERE, for our Hospital and "Mess Hall".

 

TOP view, of Stainless Steel items produced HERE.

 

1st LT HANLEY orients SGT Saunders to the new "Double Wall Lockers" being manufactured for our BARRACKS housing units. These Double Wall Lockers will have 3 drawers on the lower right side, a shelf on the upper left, a closet pole for hanging up uniforms, an unbreakable LEXAN plastic mirror mounted to the back wall, two front doors hinged on the outer walls, with a padlock "hasp" attached externally where the doors come together in the middle. If you do not have a small functional padlock, we can provide a correct sized one, that is separately keyed, so your action figures can secure their personal stuff.

 

U.S. 10th Special Forces Group (Airborne) Founder, COL AARON BANK, takes Journalists from our "Public Information Office" on a tour of the "Fort KAFFENBERGER Cabinet Shop", to show off the new furnishings for our "Basic Combat Training" Barracks. The above grouping shows the furniture items needed to accomodate 2 recruit Soldiers, as they receive their first 9 weeks of "Resident Training". The recruits are purposely grouped in close quarters for these first 9 weeks, so that they develop teamwork, "unity of purpose", and "unity of command", all essential to achieving victory. We are honored to have COL BANK with us as a highly valuable advisor on the training of the Soldiers assigned/attached to the U.S. 21st SFG-RPA, JUWTF SOG. NOTE: The actual humanity U.S.A. Hero of World War 2, COLONEL AARON BANK took his position with GOD in Heaven on 1 April 2004; he passed away in San Clemente, California USA.

 

Applying "Primer" Paint to items being manufactured.

Please help us grow the "U.S. 21st SFG-RPA, JUWTF SOG", by making a donation to acquire more materials, equipment,

pay for web server costs, and pay for permits and licenses needed, etc.. Click on the button directly below: